Commercial Water Heaters
Residental Water Heaters
Commercial Water Heaters
NON NOx Commercial Water Heaters
Bradford White® NON NOx Commercial Water Heaters
Commercial Flue Damper Millivolt-Powered Energy Saver Gas Water Heaters
Item # DM-80T-180E-3X
Item # DM-80T-180E-3X, Commercial Flue Damper Millivolt-Powered Energy Saver Gas Water Heaters
Email This Page
Save To Favorites
Unit of Measure:
Gas Connection Diameter
Relief Valve Opening
Standard Approximate Shipping Weight
Low NOx Compliance
Liquid Propane Gas
Flue Damper Millivolt Ignition
Recovery at 40 ºF Degree Rise
Recovery at 22 ºC Degree Rise
Recovery at 100 ºF Degree Rise
Recovery at 56 ºC Degree Rise
Recovery at 140 ºF Degree Rise
Recovery at 78 ºC Degree Rise
Schematic Drawing for Commercial Flue Damper Millivolt-Powered Energy Saver Gas Water Heaters
Top Vent Height A
Jacket Diameter B
Vent Diameter C
Front Hot Water Connection D
Floor to Gas Connection E
Front Cold Water Connection F
Floor to Top of Heater H
Floor to Top Water Connection J
All gas water heaters are certified at 300 psi test pressure (2068 kPa) and 150 psi working pressure (1034 kPa). All models are design certified by CSA® International (formerly AGA/CGA), ANSI standard Z-21.10.3, for up to 180 ºF (82 ºC) application as an Automatic Storage Heater, and an Automatic Circulating Tank Heater. As an Automatic Storage Heater, all models are complete, self-contained water heating systems. It needs no separate storage tank, pump, wiring or elaborate piping network. When equipped with a mixing valve, it will supply 180 ºF (82 ºC) sanitizing and lower temperature general purpose hot water simultaneously. These models can be used either as a single unit or in multiples connected in series or parallel (recommended).
Dimensions and specifications subject to change without notice in accordance with our policy of continuous product improvement.
The Commercial Flue Damper Models feature:
Automatic Flue Damper - Reduces stand-by loss, saving gas consumption and improving overall efficiency.
Hand Hole Cleanout - Allows inspection of the tank interior and facilitates the removal of sediment deposits.
Millivolt-Powered Control - No external electrical source is required for operation. An adjustable thermostat can be set up to 180 ºF (82 ºC).
Factory Installed Hydrojet® Sediment Reduction System - Cold water inlet sediment reducing device helps prevent sediment build up in the tank.
Vitraglas® Lining - Bradford White tanks are lined with an exclusively engineered enamel formula that provides superior tank protection from the highly corrosive effects of hot water. This formula (Vitraglas®) is fused to the steel surface by firing at a temperature of over 1600 ºF (871 ºC).
Water Connections - Factory installed true dielectric waterway fittings extend heater life and ease installation. Multiple water connection locations allow for greater installation flexibility.
E.C.O. - An automatic re-set Energy Cut Off (E.C.O.) shuts off all gas in the event of an overheat condition. This automatically resets when operation conditions are back to normal.
Non-CFC Foam Insulation - Covers the sides and top of tank, reducing the amount of heat loss. This results in less energy consumption, improved operation efficiencies and jacket rigidity.
Magnesium Anode Rods - Provide added protection against corrosion for long trouble-free service.
Sanitizing Capability - Temperature setting up to 180 ºF (82 ºC).
Low NOx Construction Available.
T&P Relief Valve - Installed.
Low Restriction Brass Drain Valve - Durable tamper proof design.
NSF construction available.
North Carolina Code Compliant.
ASME code available on all models above 200,000 BTU/Hr.
3-Year Limited Tank Warranty / 1-Year Limited Warranty on Component Parts.
Meet or exceed ASHRAE 90.1b (Current standard) C.E.C. Listed.
Standards for Commercial Flue Damper Millivolt-Powered Energy Saver Gas Water Heaters
Commercial Flue Damper Millivolt-Powered Energy Saver Gas Water Heaters (DM-80T-180-3N)
Brochure for Commercial Flue Damper Millivolt-Powered Energy Saver Gas Water Heaters