Catalog
Unit of Measure

Specifications

Manufacturer

N/A State®

Storage Capacity

N/A 81 U.S. gal

Input Power

N/A 270000 BTU/hr

First Hour Rating

N/A 319 gal

Gas Connection

N/A 3/4 in

Approximate Shipping Weight

N/A 547 lb

Inlet Water Connection

N/A 1-1/2 in

Outlet Water Connection

N/A 1-1/2

Thermal Efficiency

N/A 80 %

Working Pressure

N/A 160 psi

Style

N/A State Titan®

Size

N/A C

Type

N/A Natural Gas

Industry Standards

N/A ASHRAE 90.1b-1992 ASME Certified C.E.C. Listed UL® Listed

Maximum Recovery

Recovery at 80 ºF Temperature Rise

N/A 324 gal

Recovery at 100 ºF Temperature Rise

N/A 262 gal

Recovery at 140 ºF Temperature Rise

N/A 187 gal

Dimensions

Schematic

N/A
Schematic Drawing for Titan™ Commercial Gas Water Heaters

Dimension A

N/A 74-3/4 in

Dimension B

N/A 65 in

Dimension C

N/A 26-3/4 in

Dimension D

N/A 6 in

Dimension E

N/A 21-3/8 in

Dimension G

N/A 27-3/4 in

Dimension H

N/A 38 in

Dimension J

N/A 85-1/4 in

Features

Features

N/A
  • Meets ASHRAE 90.1b-1992, and C.E.C. and New York Codes for thermal efficiency and standby loss.
  • Glass-Lined Tank - Exclusive corrosion protection with glass-lining. Multiple anodes provide corrosion protection.
  • Power Gas Burner - Electronic flame monitoring with direct spark ignition. For added safety, all units are equipped with redundant gas valves. Power gas burner requires 120 volt 60 Hz service. A negative draft is required in the vent piping. This is not a forced draft burner.
  • Fully Automatic Controls - Safety shut off, high temperature limit control, dual thermostat (adjustable 120 ºF thru 180 ºF) for accurate temperature control. Maximum inlet gas pressure 14" W.C.
  • Foam Insulation - Saves fuel, helps reduce standby heat loss.
  • Jacket - made of heavy gauge steel with baked enamel finish over bonderized undercoat.
  • Fully Certified by U.L.
  • ASME Construction - Available on GPG81 140, GPG81 199, GPG81 270 & GPG81 370. When specifying ASME construction, add the letter A" at the end of the model number. 160 psi working pressure.
  • A.G.A./ASME Rated Temperature & Pressure Relief Valve - Factory installed.
  • Barometric Draft Damper - To ensure proper draft for maximum efficiency.
  • Easy Cleaning - Handhole cleanout(s) allows easy cleaning. Professional Startup Service - Furnished to assure most efficient combustion and safe initial operation.

Limited Warranty Outline

Limited Warranty Outline

N/A
  • If the tank should leak any time during the first three years, under the terms of the warranty, State Water Heaters will furnish a replacement heater; installation, labor, handling and local delivery extra.
  • NOTE: This Outline is NOT a Warranty. For complete information, consult the written warranty or State Water Heaters.

Other Features

Other Features

N/A
  • Two layers of high temperature ceramic fiber insulation in combustion chamber
  • Flame inspection port opening
  • Mounted on rugged channel iron skids
  • Multiple anodes for protection

Options

Options

N/A
  • Illinois School Code on GPG81 199 to GPG81 370
  • National Board Registration (ASME models only)
  • Low water cutoff
  • 5 or 10 year extended limited warranty
  • ASME (ON SELECTED MODELS)

Note

Note

N/A CAUTION: Unit must be installed on non-combustible surface.

To compensate for the effects of high altitude areas above 2000 feet, recovery capacities should be reduced approximately 4% for every 1000 feet above sea level.

Above capacities are based on actual efficiencies obtained in engineering laboratories.