Print Back
Unit of Measure

Specifications

Manufacturer

N/A Bradford White®

Capacity

N/A 80 U.S. gal67 Imp. gal303 L

Approximate Shipping Weight

N/A 190 lb86 kg

Power

N/A 2000 W

Wattage Limitations for Simultaneous Operation

N/A 2000 W/2000 W

Voltage for Simultaneous Operation

N/A 208 V240 V277 V480 V

Wattage Limitations for Non-Simultaneous Operation

N/A 2000 W/2000 W

Voltage for Non-Simultaneous Operation

N/A 120 V208 V240 V277 V480 V

Test Pressure

N/A 300 psi2068 kPa

Working Pressure

N/A 150 psi1034 kPa

Electrical Connection

N/A 3/4 in19 mm

Style

N/A Dairy Barn

Size

N/A C

Type

N/A Electric

Industry Standards

N/A C.E.C. Listed CSA® Certified

Maximum Recovery

Recovery at 60 ºF Temperature Rise

N/A 14 gal/h

Recovery at 80 ºF Temperature Rise

N/A 10 gal/h

Recovery at 90 ºF Temperature Rise

N/A 9 gal/h

Recovery at 100 ºF Temperature Rise

N/A 18 U.S. gal/h15 Imp. gal/h68 L/h8 gal/h

Recovery at 120 ºF Temperature Rise

N/A 7 gal/h

Dimensions

Schematic

N/A
Schematic Drawing for Commercial Dairy Barn Energy Saver Electric Water Heaters

Floor to Heater Top A

N/A 63 in1600 mm

Jacket Diameter B

N/A 24 in610 mm

Floor to Water Connection C

N/A 64-5/8 in1641 mm

Floor to T and P Connection D

N/A 63 in1600 mm

Features

Features

N/A
  • Fully Automatic Controls - Fast acting surface-mount thermostats for automatic temperature control up to 180 ºF (not recommended for sanitization purposes). Factory installed sensitive manual reset energy cutoff for safety to prevent overheating.
  • Direct Heat Transfer with Immersed Elements - Transfers heat directly and efficiently to the water. Screw-in style.
  • Factory Installed Hydrojet® Total Performance System - Cold water inlet sediment reducing device helps prevent sediment build up in tank.
  • Vitraglas® Lining - Bradford White tanks are lined with an exclusively engineered enamel formula that provides superior tank protection from the highly corrosive effects of hot water. This formula (Vitraglas®) is fused to the steel surface by firing at a temperature of over 1600 ºF (871 ºC).
  • 2" Non-CFC Foam Insulation - Covers the sides and top of the tank, reducing the amount of heat loss. This results in less energy consumption, improved operation efficiencies and jacket rigidity.
  • Water Connections - 3/4" NPT factory installed true dielectric fittings.
  • Factory Installed Heat Traps - Design incorporates a flexible disk that reduces heat loss in piping and eliminates the potential for noise generation.
  • Protective Magnesium Anode Rod - Provides added protection against corrosion for long trouble-free service.
  • 4" Leg Kit - Provides access for cleaning under the water heater.
  • Simultaneous and Non-Simultaneous Operation Available - Simultaneous operation indicates when both elements are being heated at the same time. Non-Simultaneous operation indicates when one element is being heated at a time.
  • Voltages Available - 120 V, 208 V, 240 V, 277 V, 480 V.
  • Single Phase or Three Phase Operation Available - 120 V and 277 V may only be wired for single phase operation.
  • T&P Relief Valve - Installed.
  • Low Restriction Brass Drain Valve - Durable tamper proof design.

General Information

General Information

N/A All models ETL listed. These heaters are wired inter-locking (Non-Simultaneous, Single Phase) 240 V with two 4500 W elements, unless otherwise specified.

All water and electrical connections are 3/4" (19 mm), All models certified at 300 psi test pressure (2068 kPa) and 150 psi working pressure (1034 kPa).

Dimensions and specifications subject to change without notice in accordance with our policy of continuous product improvement.

Warranty

Warranty

N/A
  • 3-Year Limited Tank Warranty / 1-Year Limited Warranty on Component Parts.