Print Back
Unit of Measure

Specifications

Manufacturer

N/A Bradford White®

Capacity

N/A 75 U.S. gal63 Imp. gal284 L

Input Power

N/A 76000 BTU/hr22.3 kW

Type

N/A Natural Gas

Style

N/A Light-Duty Eco Ultra Low NOx Power Vent

Size

N/A C

Test Pressure

N/A 300 psi2068 kPa

Working Pressure

N/A 150 psi1034 kPa

Gas Connection

N/A 1/2 in13 mm

Industry Standards

N/A ANSI ASHRAE 90.1b (Current Standards) C.E.C. Listed CSA® Certified

Maximum Recovery

Recovery at 100 ºF Temperature Rise

N/A 74 U.S. gal/h62 Imp. gal/h

Recovery at 56 ºC Temperature Rise

N/A 280 L/h

Dimensions

Schematic

N/A
Schematic Drawing for Light Duty Commercial TTW®4 Ultra Low NOx Power Vent Energy Saver Gas Water Heaters

Floor to Vent Connection A

N/A 68-7/8 in1749 mm

Jacket Diameter B

N/A 26 in660 mm

Vent Size C

N/A 3 in76 mm

Floor to T and P Connection D

N/A 51-7/8 in1318 mm

Floor to Gas Connection E

N/A 14-3/4 in375 mm

Floor to Space Heating Return F

N/A 16-1/2 in419 mm

Floor to Space Heating Outlet G

N/A 51-7/8 in1318 mm

Floor to Heater Top H

N/A 58-7/8 in1495 mm

Floor to Water Connection J

N/A 60-1/4 in1530 mm

Depth K

N/A 29-1/8 in740 mm

3" Vent Pipe

Maximum Equivalent Length for 3" Vent Pipe

N/A 50 ft

Minimum Equivalent Length for 3" Vent Pipe

N/A 7 ft

One 90º Elbows for 3" Vent Pipe

N/A 55 ft

Two 90º Elbows for 3" Vent Pipe

N/A 50 ft

Three 90º Elbows for 3" Vent Pipe

N/A 45 ft

4" Vent Pipe

Maximum Equivalent Length for 4" Vent Pipe

N/A 180 ft

Minimum Equivalent Length for 4" Vent Pipe

N/A 15 ft

One 90º Elbows for 4" Vent Pipe

N/A 175 ft

Two 90º Elbows for 4" Vent Pipe

N/A 170 ft

Three 90º Elbows for 4" Vent Pipe

N/A 165 ft

Features

Features

N/A
  • Ultra Low NOx Burner with Primary and Secondary Air Distribution Devices - Ensures proper air to gas ratio for reduction of NOx generated by the combustion process.
  • Bradford White ICON System™ - Intelligent gas control with spark to pilot ignition system eliminates the constant burning pilot. This results in savings of pilot gas during stand by periods (120 V.A.C.).
    • Enhanced Performance - Proprietary algorithms provide enhanced First Hour Delivery ratings and tighter temperature differentials.
    • Advanced Temperature Control System - Microprocessor constantly monitors and controls burner operation to maintain consistent and accurate water temperature levels.
    • Intelligent Diagnostics - An exclusive green LED light prompts the installer during start-up and provides ten different diagnostic codes to assist in troubleshooting.
    • Separate Immersed Thermowell - High strength advanced polymer composite thermowell provides isolation between electric temperature sensor and surrounding water. No need to drain the tank when removing gas valve.
  • Compatible with Optional Accessory Packages - Performance Package, Protection Package and Inlet Shut-off Valve.
  • Powerful Blower Motor - Our significantly quiet design has greater resistance to outside winds and the power to vent in many difficult venting situations.
  • Horizontal and Vertical Venting - With 3" or 4" PVC, ABS or CPVC (Maximum equivalent vent length on reverse side).
  • Factory Installed Hydrojet®2™ Total Performance System - Cold water inlet sediment reducing device helps prevent sediment build up in tank. Increases first hour delivery of hot water while minimizing temperature build up at top of tank.
  • Vitraglas® Lining - Bradford White tanks are lined with an exclusively engineered enamel formula that provides superior tank protection from the highly corrosive effects of hot water. This formula (Vitraglas®) is fused to the steel surface by firing at a temperature of over 1600 ºF (871 ºC).
  • 2" Non-CFC Foam Insulation - Covers the sides and top of tank, reducing the amount of heat loss. This results in less energy consumption, improved operation efficiencies and jacket rigidity.
  • Water Connections - 3/4" NPT factory installed true dielectric fittings.
  • Factory Installed Heat Traps - Design incorporates a flexible disk that reduces heat loss in piping and eliminates the potential for noise generation.
  • Protective Magnesium Anode Rod.
  • 3/4" NPT Side Connections.
  • Pedestal Base.
  • T & P Relief Valve - Included.
  • Low Restriction Brass Drain Valve - Durable tamper proof design.
  • Complies with the latest ultra-low NOx requirement (10 ng/J NOx limit).

General Information

General Information

N/A All gas water heaters are certified at 300 psi (2068 kPa) test pressure and 150 PSI (1034 kPa) working pressure.

All water connections are 3/4" NPT (19 mm) on 11" (279 mm) centers. All gas connections are 1/2" (13 mm).

All models design certified by CSA® International (formerly AGA/CGA), ANSI Z-21.10.1 (Z-21.10.3 for the 75 gallon) and peak performance rated.

Dimensions and specifications subject to change without notice in accordance with our policy of continuous product improvement.

Suitable for Water (Potable) Heating and Space Heating.

Toxic chemicals, such as those used for boiler treatment, shall NEVER be introduced into this system. This unit may NEVER be connected to any existing heating system or component(s) previously used with a non-potable water heating appliance.

Warranty

Warranty

N/A
  • 5-Year Limited Tank Warranty.
  • 1-Year Limited Warranty on Component Parts.

Note

Note

N/A Meet or exceed ASHRAE 90.1b (Current standard) C.E.C. Listed 80% Recovery Efficiency.

All models comply with the latest Ultra-Low NOx requirements of 10 ng/J or less.

Meets NAECA Requirements.

Available in Natural Gas only.

110 V.A.C. Required for Power Venting/110 V.A.C. 60 Hz 3.1 Amperes.